DYSON DC04 PROBLEM SOLVING

DC19T2 – Remove the cyclone and bin, open the lid at the top of the machine and wash the circular filter. Bought a Dyson DC24, for its lightness and ease of use, in the early days of production. DC19 – Remove the cyclone and bin, open the lid at the top of the machine and wash the circular filter. They are a hand-held. If the machine has no suction at the lower hose, you must check the carriage mechanism where the valve cover lifts out from to make sure it is switching over when the machine is reclined.

DC26 – Looking at the Dyson from the front turn it onto its left hand side, unscrew the two coloured plastic screws on the bottom and wash the rectangle filter, next there is a coloured catch at the rear of one of the large right hand wheel looking at it from the front Unclip this catch and open the wheel hatch and wash the doughnut style filter inside. If the handle is clear pull the U-bend off at the back of the machine, you should be able to put your fingers in each end and touch them. Before you give the favourite answer of “I never had one” If you have owned the vacuum cleaner for 3 months or more with no problems, trust me you had one. Angus Black on October 21st, at 4: Angus Black on November 12th, at 4: DC22 – Looking at the Dyson from the front turn it onto its right hand side, Use a coin to open the 2 blue screws and remove the rectangular HEPA filter.

And clutch stripping instructions are here: A quick note for Dyson DC07 owners: Thank you for your help! A quick spray of wd and put everything back together and hey presto. This mainly occurs when the cage that holds the washable filter becomes blocked and cannot be cleaned resulting in loss of suction across the whole machine.

  MYSTLINE HOMEWORK EDIT

dyson dc04 problem solving

I have a new Dyson Animal DC59 but the roller only works intermittently. What you have there is a broken loom in the hinging mechanism. You want either a new clutch or a clutch refurb.

The Brush Roll Won’t Turn – Dyson DC04, Dyson DC07 and Dyson DC14

You can follow any responses to this entry through the RSS 2. DC27 – Looking at the Dyson from the front, wash the filter at the bottom right of the machine and also the HEPA filter underneath the bin.

dyson dc04 problem solving

Dyson Spares – The Dyson Forums. It sound that your DC15 have an electric issue, may be electronics.

Welcome to Dyson

Any question please call or stop by at S University Blvd. You can follow any responses to this entry through the RSS 2.

I have taken the roller out and checked for blockages on the roller and edges but as I say it is new, so it is hardly dirty. Brad Mastro on June 22nd, at 5: Hi Angus ydson a DC04 and does not pick up dirt etc properly and have discovered broken belt where can i get a new belt cheers. Next use a a coin to open the blue screw next to the large wheel, open the wheel hatch and remove the large cylinder filter.

Mutimer on February 27th, at 1: Had a look at the DC24 recently and fyson that the brush roller at the drive end and clutch were causing the roller to wobble about like a bandy provlem. I can see from your connection you are in Colorado, if Littleton is anywhere near you, this guy will be able to do it: Suction problems are mainly due to blockages or dirty filters.

  DRUCKKOSTENZUSCHUSS DISSERTATION STIPENDIUM

Cheryl Sweeney on March 8th, at DC18 – Wash the filter above the bin in the cyclone top. I have taken the roller out and checked for blockages on the roller and edges but as I say lroblem is new, so it is hardly dirty.

Dyson vacuum cleaner suction problems troubleshooting – not picking up

I was able to turn it off then back on and it would start again, only to stop after a few seconds. Angie Tackett on October 12th, at 4: If you have a ball model or one of the later uprights such as the DC27, it could be the hose has not transferred over properly.

Mutimer on February 27th, at 1: Help from Dyson experts. Caren Quinn on January 17th, at 9: This mainly occurs when the cage that holds the washable filter becomes blocked and cannot be cleaned resulting in loss of suction across the whole machine. It worked Ok for six months or so until it began to sound like a very large and powerful tractor. I reclined it with it on carpet and still nothing.

Did Dyson keep the direct drive of the roller brush. I replaced the belt but it burnt through straight away.